How To Fit Skirting Boards

This can be a tricky job but if you follow our instructions youll have no problem. Screw the boards into the studs inside a plaster wall instead of using glue.


How To Fit Skirting Board Fitting Skirting Boards Flush Trim Router Bit Skirting

Run a bead of contact adhesive down each adhesive channel Fig 2 on the back of skirting and push firmly to the wall.

How to fit skirting boards. Easy to present and for the most part available either pre-arranged or pre-finished MDF has gotten a standard choice for skirting board in new homes. Cut the skirting board with the scribed joint to size then push it against the first skirting board so. Drill a small hole at the bottom of the board so you dont have to cut all the way down.

Plan the way your boards go in to avoid the need for a board with scribes at both ends. Repeat this pattern at 500mm along the length of the skirting. To fit your skirtings using this method you will need to fit the first board right into the corner.

Watch our step-by-step film showing how to fit skirting boards with expert advice and top tips to help you complete the job with confidence. How to Fit Skirting Boards. Find the studs in the plaster wall and mark their position on the wall and on the skirting board.

See the other. If the fit isnt exact lightly sand down the end to achieve a better fit. I never Butt join two boards together end to end square I always join them together with a mitre between 30-45.

Firstly drill a small hole in your skirting board. This article includes a step-by-step guide on skirting board installation. However for corners mitred angled cuts are required use a mitre block to provide the correct angle of cut for joining lengths.

Slide the board back a little and mark these positions on the wall with a pencil X. When youre happy with the location drill a hole into the skirting using a wood drill bit. Fig 1 Mark measurement on a length of skirting and cut to size using a fine toothed saw.

If youre happy with the way they look you can cut or mitre the other end of the scribed board to length. Avoid cutting the wall or wallpaper by protecting it with some corrugated cardboard. If youre fixing the skirting to a masonry wall then use a 6mm masonry drill bit to drill through the skirting and into the wall.

When joining skirting to an architrave a straight cut is all that is required. Watch our step-by-step video showing how to fit skirting boards with expert advice and top tips to help you complete the job with confidence. MDF skirting is commonly stacked and as often as possible the supported choice.

Then mark the wall behind where the skirting will go. Timber merchants suggest skirting sheets. See the other p.

When fitting skirting boards if a single skirting board length isnt enough to cover a wall in one piece you will need to cut a Lengthening Joint. You will need to fit your skirting boards in place first drill a small hole through the skirting board where you want the nail to be and drill through until it marks the plaster behind the skirting. If you want to screw the boards to a plasterboard wall mark the position of the wooden studs and then put a pilot drill through the skirting board and the wall at these points.

Drill a pilot hole into. Use a piece of wood to guide and steady your tenon saw as you cut the skirting board. Woodies will show you how to fit skirting boards.

Check the fit of the two boards. LENGTH 1 – Measure from the outside edge of door architrave to corner of room. Remember to always screw at 600mm centres.

Start the holes 50mm from the end of the wall and position each one 25mm from the top and bottom of the skirting. Attach the skirting board to the wall with the nail gun to so that it is flush to the corner. You can now fit the rawl plug and screw the board to the wall.

Position both skirting boards together in the internal corner ensuring that the scribed joint fits into the profile of the skirting. Make sure these holes line up when the skirting is in place. Make sure the end of the first board butts up to the wall when you fit it.

If you are looking to put new skirting boards in your home we will go over how to install skirting boards the tools materials and safety equipment needed and some frequently asked questions about fitting skirting boards. When adjacent lengths have been mitred position them and check that they join neatly and are level. If you are fixing to a solid wall run a pilot drill through the skirting board.

Scribing both ends of a board calls for. The second board will then need to be cut at the end using profile cutting in order to fit over the first piece of skirting. Cut the board at a 45-degree angle.

Remember to make the cut at the other end of the skirting before fitting them. Mark up the skirting board so that fixing points are around 2cm below the slope of the skirting at around 60cm intervals. Next use the drill to make a hole in the wall behind where your skirting board will sit.

Such a skirting board generally comes in two sorts.


How To Fit Skirting Board Fitting Skirting Boards Skirting Boards Skirting


How To Fit Skirting Boards Homebuilding Renovating Skirting Boards Skirting Renovations

admin

Leave a Reply

Your email address will not be published. Required fields are marked *

Post comment